The Drain Pump series are all pre-assembled packaged pumping stations for use in areas where gravity flow is not available. They are used for various drainage applications, with the 912 series also used for the transfer of sewage or waste water, all specially designed for easy installation.

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

A Siren Alarm is recommended to ensure that there is no excess build up in the event of a pump failure.

*For Additional Information please see the PDF link*

912pdf 900pdf 105pdf INSTALLATIONpdf

These packaged pumping stations consist of a moulded polyethylene sump suitable for below ground applications, that come supplied with a single 240volt pump suitable for drainage water and light sewage applications.

Automatic operation is standard with the use of an integral floatswitch fitted to the pump, with flexible hose internal pipework connected to an external BSP thread.

A Siren Alarm is recommended to ensure that there is no excess build up in the event of a pump failure.

*For Additional Information please see the PDF link*

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

AES350/1500pdf

The AES below ground 1 metre diameter packaged pumping stations are designed for sewage and drainage water transfer applications in domestic and commercial properties.

The tank comes complete with a single free standing 2inch submersible pump in 240v, with other sizes available on request. Also featuring flexible hosing, fittings & valves, lifting chain, a manhole cover with frame and a siren alarm unit with dual floatswitches for automatic operation.

NOTE: Comes fitted with flexible hose and not internal rigid pipework as pictured.

*For Additional Information please see the PDF link*

The inlets or vents are cut to the customers requirements - see the following link for reference: Customer Fabrication Instructions

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

NOTE - Models below are described as follows:
(DIAMETER) / (DEPTH) - (PUMP SIZE)

INSTALLATIONdoc FABRICATION-INSTRUCTIONpdf

These packaged pumping stations consist of a one piece moulded polyethylene sump suitable for above and below ground applications. Supplied with two 240volt pumps suitable for drainage water and light sewage applications. Automatic operation is standard with the use of an integral floatswitch fitted to the pump.

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

A Siren Alarm is recommended to ensure that there is no excess build up in the event of a pump failure.

Also available is a neck extension in order to raise the lid opening up to a higher level.

*For Additional Information please see the PDF link*

VS-400pdf INSTALLATIONdoc

The AES below ground 1 metre diameter packaged pumping stations are designed for sewage and drainage water transfer applications in domestic and commercial properties.

The tank comes complete with a single, guide rail mounted 240v submersible pump available in 2inch, 2.5inch or 3inch sizes. Also featuring internal pipework, fittings & valves, lifting chain, a manhole cover with frame and a control panel with dual floatswitches for automatic operation.

*For Additional Information please see the PDF link*

The inlets or vents are cut to the customers requirements - see the following link for reference: Customer Fabrication Instructions

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

NOTE - Models below are described as follows:
(DIAMETER) / (DEPTH) - (PUMP SIZE)

INSTALLATIONdoc FABRICATION-INSTRUCTIONpdf

The AES below ground 1 metre diameter packaged pumping stations are designed for sewage and drainage water transfer applications in domestic and commercial properties.

The tank comes complete with a single, guide rail mounted 415v submersible pump available in 2inch, 2.5inch or 3inch sizes. Also featuring internal pipework, fittings & valves, lifting chain, a manhole cover with frame and a control panel with dual floatswitches for automatic operation.

*For Additional Information please see the PDF link*

The inlets or vents are cut to the customers requirements - see the following link for reference: Customer Fabrication Instructions

All our pumping stations comply to BS EN 12050-1:2001 / BS EN 752-6:1998 standards.

NOTE - Models below are described as follows:
(DIAMETER) / (DEPTH) - (PUMP SIZE)

INSTALLATIONdoc FABRICATION-INSTRUCTIONpdf